TFT100 First Start

Small, professional and waterproof tracker for forklifts, E-mopeds and E-scooters with internal high gain GNSS/GSM antennas, Bluetooth, high capacity internal Li-ion battery and 10-97 V power supply range.

How to insert Micro-SIM card

1. Remove the bottom cover.
2. Insert Micro-SIM card as shown with PIN request disabled or read Security info how to enter it later in Configurator. Make sure that Micro-SIM card cut-off corner is pointing forward to slot.
3. Connect the battery as shown to the device.
4. After configuration, attach device cover and put the screws back in.
5. Device is ready to be connected.

Micro-SIM card insertion/removal must be performed when device is powered off – external voltage and battery are disconnected. Otherwise Micro-SIM card might be damaged or device will not detect it.

Cable colors

TFT100 CAN PINOUT

TFT100 RS232 PINOUT

TFT100 RS485 PINOUT

TFT100 UART PINOUT

PIN COLOR	CAN PIN NAME	CAN DESCRIPTION	RS232 PIN NAME	RS232 DESCRIPTION	RS485 PIN NAME	RS485 DESCRIPTION	UART PIN NAME	UART DESCRIPTION
Red	VCC (10-97)V DC (+)	Power supply (+10...97 V DC).	VCC (10-97)V DC (+)	Power supply (+10...97 V DC).	VCC (10-97)V DC (+)	Power supply (+10...97 V DC).	VCC (10-97)V DC (+)	Power supply (+10...97 V DC).
Black	GND (-)	Ground.	GND (-)	Ground.	GND (-)	Ground.	GND (-)	Ground.
Yellow	1WIRE POWER	Power supply pin for Dallas 1-Wire devices	1WIRE POWER	Power supply pin for Dallas 1-Wire devices	1WIRE POWER	Power supply pin for Dallas 1-Wire devices	1WIRE POWER	Power supply pin for Dallas 1-Wire devices
White/Green	CAN-H	CAN interface High.	RS232-IN	Input wire for RS232.	RS485-B	Signal wire B for RS485.	UART-RX	Input for data reception through UART.
White	CAN-L	CAN interface Low.	RS232-OUT	Output wire for RS232.	RS485-A	Signal wire A for RS485.	UART-TX	Output for data transmission through UART.
Grey	AIN 2 / DIN 2	Analog input, channel 2 / Digital input, channel 2.	AIN 2 / DIN 2	Analog input, channel 2 / Digital input, channel 2.	AIN 2 / DIN 2	Analog input, channel 2 / Digital input, channel 2.	AIN 2 / DIN 2	Analog input, channel 2 / Digital input, channel 2.
White/Orange	DOUT 1 / DIN 3	Digital output, channel 1 / Digital input, channel 3.	DOUT 1 / DIN 3	Digital output, channel 1 / Digital input, channel 3.	DOUT 1 / DIN 3	Digital output, channel 1 / Digital input, channel 3.	DOUT 1 / DIN 3	Digital output, channel 1 / Digital input, channel 3.
Violet	DOUT 2 / DIN 4	Digital output, channel 2 / Digital input, channel 4.	DOUT 2 / DIN 4	Digital output, channel 2 / Digital input, channel 4.	DOUT 2 / DIN 4	Digital output, channel 2 / Digital input, channel 4.	DOUT 2 / DIN 4	Digital output, channel 2 / Digital input, channel 4.
Green	AIN 1 / DIN 1	Analog input, channel 1 / Digital input, channel 1.	AIN 1 / DIN 1	Analog input, channel 1 / Digital input, channel 1.	AIN 1 / DIN 1	Analog input, channel 1 / Digital input, channel 1.	AIN 1 / DIN 1	Analog input, channel 1 / Digital input, channel 1.
Blue	1WIRE DATA	Data channel for 1–Wire devices.	1WIRE DATA	Data channel for 1–Wire devices.	1WIRE DATA	Data channel for 1–Wire devices.	1WIRE DATA	Data channel for 1–Wire devices.

Set up your device

PC Connection (Windows)

1. Power-up TFT100 with DC voltage 10-97 V power supply using supplied power cable. LED should start blinking, see LED behaviour description.
2. Connect device to computer using Micro-USB cable or Bluetooth connection:
   • Using Micro-USB cable:
     • You will need to install USB drivers, see "How to install USB drivers (Windows)"
   • Using Bluetooth:
     • TFT100 Bluetooth is enabled by default. Turn on Bluetooth on your PC, then select Add Bluetooth or other device > Bluetooth. Choose your device named – “TFT100_last_7_imei_digits”, without LE in the end. Enter default password 5555, press Connect and then select Done.
3. You are now ready to use the device on your computer.

How to install USB drivers (Windows)

1. Please download COM port drivers from Teltonika here.
2. Extract and run TeltonikaCOMDriver.exe.
3. Click Next in driver installation window.
4. In the following window click Install button.
5. Setup will continue installing the driver and eventually the confirmation window will appear. Click Finish to complete the setup.

Configuration (Windows)

At first TFT100 device will have default factory settings set. These settings should be changed according to the user's needs.
Main configuration can be performed via Teltonika Configurator software. Configurator operates on Microsoft Windows OS and uses prerequisite MS .NET Framework. Make sure you have the correct version installed.

MS .NET requirements
Operating system	MS .NET Framework version	Version	Link
Windows Vista Windows 7 Windows 8.1 Windows 10	MS .NET Framework 4.6.2	32 and 64 bit	www.microsoft.com

Downloaded Configurator will be in compressed archive. Extract it and launch Configurator.exe. After launch software language can be changed by clicking in the right bottom corner:

Configuration process begins by pressing on connected device:

After connection to Configurator Status window will be displayed:

Various Status window tabs display information about GNSS, GSM, I/O, Maintenance and etc. TFT100 has one user editable profile, which can be loaded and saved to the device. After any modification of configuration the changes need to be saved to device using Save to device button. Main buttons offer following functionality:

1. Load from device – loads configuration from device.
2. Save to device – saves configuration to device.
3. Load from file – loads configuration from file.
4. Save to file – saves configuration to file.
5. Update firmware – updates firmware on device.
6. Read records – read records from device.
7. Reboot device – restarts device.
8. Reset configuration – sets device configuration to default.

Most important configurator section is GPRS – where all your server and GPRS settings can be configured and Data Acquisition – where data acquiring parameters can be configured. More details about TFT100 configuration using Configurator can be found in the manual.

Quick SMS configuration

Default configuration has optimal parameters present to ensure best performance of track quality and data usage.
Quickly set up your device by sending this SMS command to it:

"  setparam 2001:APN;2002:APN_username;2003:APN_password;2004:Domain;2005:Port;2006:0"

GPRS settings:

• 2001 – APN
• 2002 – APN username (if there are no APN username, empty field should be left)
• 2003 – APN password (if there are no APN password, empty field should be left)

Server settings:

• 2004 – Domain
• 2005 – Port
• 2006 – Data sending protocol (0 – TCP, 1 – UDP)

Note: Before SMS text, two space symbols should be inserted.

Default configuration settings
Movement and ignition detection:
	Vehicle movement will be detected by accelerometer		Ignition will be detected by vehicle power voltage between 10 – 97 V
Device makes a record On Moving if one of these events happen:
	300 seconds passes		Vehicle turns 10° degrees
	Vehicle drives 100 meters		Speed difference between last coordinate and current position is greater than 10 km/h
Device makes a record On Stop if:
	1 hour passes while vehicle is stationary and ignition is off
Records sending to server:
	If device has made a record it is sent to the server every 120 seconds

After successful SMS configuration, TFT100 device will synchronize time and update records to configured server. Time intervals and default I/O elements can be changed by using Teltonika Configurator or SMS parameters.

External links

https://teltonika-mobility.com/product/e-scooter-tracker-plus/

https://teltonika-mobility.com/product/e-forklift-tracker-plus/