TFT100 Short-term firmware

From Wiki Knowledge Base | Teltonika Mobility
Main Page > Electro-Mobility > TFT100 > TFT100 Firmware and Configurator > TFT100 Short-term firmware
SHORT-TERM FIRMWARE
FIRMWARE VERSION: 55.01.11.Rev.00
CONFIGURATOR VERSION: 1.6.11_R.41
RELEASE DATE:
2022-09-16
DOWNLOAD
Firmware
Configurator
DOWNLOAD ALL
DOWNLOAD ALL


CHANGELOG
VERSION RELEASE DATE CONFIGURATOR CHANGES FIRMWARE CHANGES KNOWN ISSUES
55.01.11.Rev.00
1.6.11_R.41
2022-09-16
  • [CHN] Changed minimum BLE scan start period configuration value.
  • [ADD] TFT100: Added CAN Debug protocol and CAN Log parameter.
  • [CHN] Increased DOUT duration limit for Overspeeding, Green Driving, Idling features
  • [CHN] Changed minimum BLE scan start period configuration value.
  • [FIX] Fixed REC MSG queue filling by suspending CAN data reading.
  • [CHN] Increased DOUT duration limit for Overspeeding, Green Driving, Idling features
  • [ADD] Added CANDebug protocol.
  • [FIX] Fixed Beacon record saving on Disabled discovery parameter.
  • [FIX] Fixed time synchronization issues.
  • [FIX] Implemented accelerometer changes to prevent unwanted wake-up and fake movement.
  • [ADD] Added GPS Track data renewing immediately after difference detected.
  • [FIX] Fixed beacons buffer cleanup after the end of BLE scanning or periodic beacon record creation.
  • If the BLE record period is configured to 60sec, every second record is without the date, if it is configures every 5sec period, quantity of records without the date increases. If the eventual records is configured, issue does not reoccur.
  • Incorrect CAN ID may appear from time to time when using CAN Debug.
VERSION RELEASE DATE CONFIGURATOR CHANGES FIRMWARE CHANGES KNOWN ISSUES
55.01.10.Rev.00*
1.6.11 R.39
*was approved as STABLE
2022.08.01
  • [CHN]: Changed Default and Minimum CAN Command period. Changed tooltips.
  • [ADD]: Add timestamp backup description
  • [CHN]: Corrected misleading and outdated tooltips
  • [CHN]: Changed TFT100 default configuration.
  • [ADD]: Added CAN I/O reset parameter.
  • [FIX]: Fixed BLE Sensor Custom IO SMS sending with value NaN and displaying as ASCII in Configurator.
  • [FIX]: Fixed device constantly opening and closing GPRS with permanent link if APN is empty in configurator.
  • [FIX]: Fixed permanent link not changing protocol after reconfiguration.
  • [CHN]: Updated FOTA WEB protocol ID 0x04 => 0x05
  • [FIX]: Increased connection interval in order to speed up connection through BLE terminal.
  • [FIX]: Fixed POSI command skipping.
  • [FIX]: Fixing network stability issues.
  • [FIX]: Fixed timestamp not renewing for Eddystone beacons.
  • [FIX]: Added condition to prevent closing socket, if GPRS command is received and response was not sent yet.
  • [FIX]: Fixed issue, when after pin reconfiguration from DOUT to DIN, DOUT stays ON.
  • [FIX]: Fixed periodic CAN command message disabling.
  • [FIX]: Fixed Flex CAN protocol reading 0 values after power is cut off.
  • [FIX]: Fixed Manual CAN commands periodical sending.
  • [CHN]: Changed TFT100 default configuration.
  • [CHN]: Increased external queue size to prevent abnormal restarts during BLE scan.
  • [ADD]: Added Reset CAN IO values parameter.
  • [FIX]: Fixed CAN message sending irregularities.
  • [FIX]: Fixed J1939 CAN reading recovery after external power is off.
  • [ADD]: Added priority for charger control factory command.
  • [FIX]: Fixed a broken GSM connection due to incorrect SIM card selection.
55.01.06.Rev.00
1.6.11_R.35
2022.02.18
  • [ADD]: Govecs FLEX (TFT100) changes were merged into 7.0.33 version.
  • [FIX]: Fixed FOTA WEB fail when the files requested for download do not exist.
  • [FIX]: Fixed lost BLE AES encryption key after reboot.
  • [ADD]: Merged Govecs FLEX changes into base. New configuration 7.0.33 created also.
  • [FIX]: Fixed DOUT delay after ignition detection.
55.01.05.Rev.00
1.6.11_R.33
2022.01.17
  • [ADD]: Added AES128 BLE encryption KEY parameter
  • [CHN]: Updated tooltip description for DOUT Deactivation Via DIN
  • [FIX]: Fixed Manual CAN Ignition and Speed I/O‘s timeout issue
  • [FIX]: Fixed Manual CAN Speed Source I/O‘s Speed Offset min/max values
  • [ADD]: Added AES128 BLE encryption functionality
  • [FIX]: Fixed Manual CAN I/O triggers with configured operands
  • [FIX]: Fixed GPRS commands sending with TLS encryption
  • AES128 BLE encryption key is being lost after device reboot
  • Ignition detection delay with immobilizer feature