TFT100 System settings

From Wiki Knowledge Base | Teltonika Mobility
Main Page > Electro-Mobility > TFT100 > TFT100 Configuration > TFT100 System settings

System Settings

System settings TFT100.png

Movement Source

User can select which source will be used determine when vehicle is on stop or moving. When multiple are selected, if any of selected are active, Vehicle MOVING mode is used.

Speed source

If TFT100 is used with CAN modification extra settings option will we available for choosing Speed source. Speed source.PNG

Records settings

Here user can enable or disable records when GPS is not available (no GPS fix).

PDOP filter

User can choose to turn enable or disale the PDOP filter. This feature allows to discard GNSS module output data if PDOP (Position Dilution of Precision) value above selected threshold.

  • PDOP filter threshold - PDOP filter threshold value can be entered from which the parameters will be filtered.

LED Indication

User can turn on or off the indication LEDs.

GNSS Source settings

User can configure which GNSS system(s) to use.
User has a choice to use only one system between GPS, GLONASS, Galileo or Beidou and it is possible to choose two or three systems together. One exception is that you cannot combine BeiDou and GLONASS systems together.

Examples of non-configurable GNSS source combinations are:

  • GLONASS + BeiDou;
  • Galileo + GLONASS + BeiDou;
  • GPS + GLONASS + BeiDou;
  • GPS + Galileo + GLONASS + BeiDou.

List of configurable GNSS sources:

  • GPS only;
  • GPS + BeiDou;
  • GPS + GLONASS;
  • GPS + GLONASS + Galileo.

Battery Charge Mode

Here user can change battery charger settings, where charging is allowed. Battery will be charged: On Need (battery will be charged anytime when it needs to be charged) and After Ignition ON (battery will be charged only when ignition is on).

Analog Input Value Range

User can choose analog input range of 15 V or 150 V.

Data Protocol

User can choose which protocol version to use for data sending to server.

Input/Output Mode

User can choose specific external pins to work as an input or as output. Possible valid input/output configurations:

  • Digital input 3 and Digital input 4 (value:5),
  • Digital output 1 and Digital input 4 (value:6),
  • Digital input 3 and Digital output 2 (value:9),
  • Digital output 1 and Digital output 2 (value:10).

Static Navigation Settings

Static navigation MM.png

Static Navigation mode is a filter, which filters out track jumps when the object is stationary. If static navigation filter is disabled, it will apply no changes to GPS data. If static navigation filter is enabled, it will filter changes in GPS position if no movement (as defined by configured movement source) or ignition (as defined by configured ignition source) is detected. It allows filtering GPS jumps when the object is parked (not moving) and GPS position is still traced.
Additionally, user can choose which source (movement or ignition) is used to activate/deactivate static navigation.

Sleep Mode

User can choose sleep mode. More about sleep modes can be found here.
Sleep mode TFT100.png

Ignition Source

Ignition source.png

User can choose an ignition source from digital input 1, power voltage, CAN and accelerometer. More than one ignition source can be selected at the same moment. When there are 2 or more sources selected, at least one condition has to be met to change Ignition status. Example: DIN1 and Accelerometer are selected as Ignition source. When the device detects movement, Ignition status will change to 1, regardless that DIN1 value is 0. User can select movement start and movement stop delay time - those parameters are used when accelerometer is selected as an ignition source. Ignition status is used in power management and the following functionalities: Eco/Green driving, Excessive idling, Over speeding, Towing detection and trip.

Accelerometer Delay Settings

Accelerometer delay.PNG

Here the user can set the movement start/stop delays.
For example, if the Movement Start Delay is set to 1s and Movement Stop Delay to 60s, the movement will be detected after 1s of moving and defined as stopped after 60s when device stopped moving.

Time Synchronization

Time synchronization.PNG

User can select which NTP server (it is possible to configure up to two servers) and what time period to use to re-synchronize time.

Accelerometer auto calibration

Accelerometer auto calibration.PNG

User can disable or enable Accelerometer Auto Calibration and Gravity Filter features. Under Accelerometer Auto Calibration settings, user can choose:

  • Disable – do not use auto calibration feature (sends AXES raw data),
  • Once – calibrate one time only,
  • Continuous – launch auto calibration every trip (note: trip function must be enabled! ).

Important! If Auto calibration is disabled, device should be mounted according User manual for Eco/Green driving feature to work properly. If enabled, AXES will be reoriented to VEHICLE axes according User manual (+X – Forward, +Y – Left, +Z – Down).
Under Gravity Filter settings, user can choose:

  • Disabled – do not remove GRAVITY component from AXL/Crash data,
  • Enabled – remove GRAVITY component from AXL/Crash.

Timestamp Backup

Timestamp Backup.png

Enables or disables the Timestamp Backup synchronization.