TST100 First Start

From Wiki Knowledge Base | Teltonika Mobility
Electric Mobility > TST100 > TST100 First Start
Qsg rut950 teltonika.PNG


Professional waterproof tracker designed for E-scooters with internal high gain GNSS/GSM antennas and internal Li-ion battery.

TST100ODM.jpg

Know your device

TST100 know your device-1.png



Pinout


TST100-pinout2.png
PIN NAME JL-F39-Z508JG Cable connector PIN No.

TST100 PCB PIN No.

VCC (+) (8-50)V DC 1 1
GND (-) 5 2
RX 3 3
TX 4 4
Power Control Wire (PCW) 2 5

Note! Always double check GND and PCW PINS!

Set up your device

How to insert micro SIM card and connect the battery

  1. Remove the top cover.
  2. Insert Micro-SIM card as shown with PIN request disabled. Make sure that Micro-SIM card cut-off corner is pointing forward to slot.
  3. Connect the battery.
  4. To power up TST100, connect the plug to the E-scooter.
  5. Configure the device by connecting micro-USB from TST100 to PC.
  6. After configuration, disconnect TST100 from PC. Attach the lid and put the screws back in as shown.
  7. Device is ready to be used.

TST100 setup 1.jpgTST100 setup 2.jpgTST100 setup 3.jpg TST100 setup 4.jpgTST100 setup 5.pngTST100 setup 6.jpgTST100 setup 7.jpg


PC Connection (Windows)

  1. To power up TST100 connect to E-scooter or external (8 – 50 V) power supply using supplied power cable. LED should start blinking, see LED behaviour description.
  2. Connect device to computer using Micro-USB cable.
  3. You will need to install USB drivers, see How to install USB drivers (Windows) shown below.
  4. You are now ready to use the device on your computer.

How to install USB drivers (Windows)

  1. Please download COM port drivers from Teltonika here.
  2. Extract and run TeltonikaCOMDriver.exe.
  3. Click Next in driver installation window.
  4. In the following window click Install button.
  5. Setup will continue installing the driver and eventually the confirmation window will appear. Click Finish to complete the setup.

Configuration (Windows)

At first TST100 device will have default factory settings set. These settings should be changed according to the user's needs.
Main configuration can be performed via Teltonika Configurator software. Configurator operates on Microsoft Windows OS and uses prerequisite MS .NET Framework. Make sure you have the correct version installed.

MS .NET requirements
Operating system MS .NET Framework version Version Link
  • Windows Vista
  • Windows 7
  • Windows 8.1
  • Windows 10
MS .NET Framework 4.6.2 32 and 64 bit www.microsoft.com

Downloaded Configurator will be in compressed archive. Extract it and launch Configurator.exe. After launch software language can be changed by clicking Language icon.png in the right bottom corner:

FMB Configurator language.jpg

Configuration process begins by pressing on connected device:

TST100-Connected-screen.jpg

After connection to Configurator Status window will be displayed:

TST100-Status-screen.jpg

Various Status info tabs display information about GNSS, GSM, I/O, Maintenance and etc. TST100 has one user editable profile, which can be loaded and saved to the device. After any modification of configuration the changes need to be saved to device using Save to device button. Main buttons offer following functionality:

  1. Load from device.png Load from device – loads configuration from device.
  2. Save to device.png Save to device – saves configuration to device.
  3. Load from file.png Load from file – loads configuration from file.
  4. Save to file.png Save to file – saves configuration to file.
  5. Firmware update.png Update firmware – updates firmware on device.
  6. Read records.png Read records – read records from device.
  7. Reboot device.png Reboot device – restarts device.
  8. Reset configuration.png Reset configuration – sets device configuration to default.

Most important configurator section is GPRS – where all your server and GPRS settings can be configured and Data acquisition – where data acquiring parameters can be configured. More details about TST100 configuration using Configurator can be found here.

Quick SMS configuration

Default configuration has optimal parameters present to ensure best performance of track quality and data usage.
Quickly set up your device by sending this SMS command to it:

"  setparam 2001:APN;2002:APN_username;2003:APN_password;2004:Domain;2005:Port;2006:0"

GPRS settings:

  • 2001 – APN
  • 2002 – APN username (if there are no APN username, empty field should be left)
  • 2003 – APN password (if there are no APN password, empty field should be left)

Server settings:

  • 2004 – Domain
  • 2005 – Port
  • 2006 – Data sending protocol (0 – TCP, 1 – UDP)

Note: Before SMS text, two space symbols should be inserted.

IOS sms cfg.png
Default configuration settings
Movement detection:
Accelerometer.png E-Scooter movement will be detected by accelerometer
Device makes a record On Moving if one of these events happen:
300s icon 2.png 300 seconds passes Angle 10 2.png E-Scooter turns 10° degrees
Min distance.png E-Scooter moves 100 meters Speed delta.png Speed difference between last coordinate and current position is greater than 10 km/h
Device makes a record On Stop if:
1h icon.png 1 hour passes while E-Scooter is stationary
Records sending to server:
120 s.png If device has made a record it is sent to the server every 120 seconds


After successful SMS configuration, TST100 device will synchronize time and update records to configured server. Time intervals and default I/O elements can be changed by using Teltonika Configurator or TST100 SMS parameters.

Installation instructions for ES4 E-Scooter

  1. Connect TST100 to the E-scooter.
  2. Place plug the bracket as shown.
  3. Make sure the bracket fits well and doesn’t jam the cable inside. Use provided metal zip tie to secure it in a place. Cable tie gun needs to be used for fitting the TST100.

TST100 ES 1.jpgTST100 ES 2.jpgTST100 ES 3.jpg

Sauktukas.png Pay attention!
E-Scooter should be switched off when connecting TST100 plug. To avoid any damage double check if cable and plug are placed correctly before attaching bracket to the E-Scooter.

Installation instructions for Segway MAX E-Scooter

  1. Connect TST100 to the E-scooter.
  2. Place plug the bracket as shown.
  3. Fit bracket A first, then fit bracket B, push until it clicks to place
  4. Use provided metal zip tie to secure it in a place. Cable tie gun needs to be used for fitting the TST100.

TST100 MAX 1.jpgTST100 MAX 2.jpgTST100 MAX 3.jpgTST100 MAX 4.jpg

Sauktukas.png Pay attention!
E-Scooter should be switched off when connecting TST100 plug. To avoid any damage double check if cable and plug are placed correctly before attaching bracket to the E-Scooter.